HAL configuration template file. This file should be copied to the application folder and renamed to stm32l0xx_hal_conf.h. More...

#include "stm32l0xx_hal_rcc.h"
#include "stm32l0xx_hal_gpio.h"
#include "stm32l0xx_hal_dma.h"
#include "stm32l0xx_hal_cortex.h"
#include "stm32l0xx_hal_flash.h"
#include "stm32l0xx_hal_i2c.h"
#include "stm32l0xx_hal_pwr.h"
#include "stm32l0xx_hal_rtc.h"
#include "stm32l0xx_hal_spi.h"
#include "stm32l0xx_hal_tim.h"
#include "stm32l0xx_hal_uart.h"

Macros
#define	HAL_MODULE_ENABLED
	This is the list of modules to be used in the HAL driver.

#define	HAL_RTC_MODULE_ENABLED

#define	HAL_SPI_MODULE_ENABLED

#define	HAL_TIM_MODULE_ENABLED

#define	HAL_UART_MODULE_ENABLED

#define	HAL_GPIO_MODULE_ENABLED

#define	HAL_DMA_MODULE_ENABLED

#define	HAL_I2C_MODULE_ENABLED

#define	HAL_RCC_MODULE_ENABLED

#define	HAL_FLASH_MODULE_ENABLED

#define	HAL_PWR_MODULE_ENABLED

#define	HAL_CORTEX_MODULE_ENABLED

#define	HSE_VALUE ((uint32_t)8000000U)
	Adjust the value of External High Speed oscillator (HSE) used in your application. This value is used by the RCC HAL module to compute the system frequency (when HSE is used as system clock source, directly or through the PLL). More...

#define	HSE_STARTUP_TIMEOUT ((uint32_t)100U)

#define	MSI_VALUE ((uint32_t)2097000U)
	Internal Multiple Speed oscillator (MSI) default value. This value is the default MSI range value after Reset. More...

#define	HSI_VALUE ((uint32_t)16000000U)
	Internal High Speed oscillator (HSI) value. This value is used by the RCC HAL module to compute the system frequency (when HSI is used as system clock source, directly or through the PLL). More...

#define	HSI48_VALUE ((uint32_t)48000000U)
	Internal High Speed oscillator for USB (HSI48) value. More...

#define	LSI_VALUE ((uint32_t)37000U)
	Internal Low Speed oscillator (LSI) value. More...

#define	LSE_VALUE ((uint32_t)32768U)
	External Low Speed oscillator (LSE) value. This value is used by the UART, RTC HAL module to compute the system frequency. More...

#define	LSE_STARTUP_TIMEOUT ((uint32_t)5000U)

#define	VDD_VALUE ((uint32_t)3300U)
	This is the HAL system configuration section. More...

#define	TICK_INT_PRIORITY ((uint32_t)0U)

#define	USE_RTOS 0U

#define	PREFETCH_ENABLE 0U

#define	PREREAD_ENABLE 1U

#define	BUFFER_CACHE_DISABLE 0U

#define	assert_param(expr) ((void)0U)
	Uncomment the line below to expanse the "assert_param" macro in the HAL drivers code. More...

Detailed Description

HAL configuration template file. This file should be copied to the application folder and renamed to stm32l0xx_hal_conf.h.

Author: MCD Application Team

Attention

© Copyright (c) 2016 STMicroelectronics. All rights reserved.

This software component is licensed by ST under BSD 3-Clause license, the "License"; You may not use this file except in compliance with the License. You may obtain a copy of the License at: opensource.org/licenses/BSD-3-Clause

Macro Definition Documentation

◆ assert_param

#define assert_param ( expr ) ((void)0U)

Uncomment the line below to expanse the "assert_param" macro in the HAL drivers code.

Include module's header file

◆ HSE_STARTUP_TIMEOUT

#define HSE_STARTUP_TIMEOUT ((uint32_t)100U)

Time out for HSE start up, in ms

◆ HSE_VALUE

#define HSE_VALUE ((uint32_t)8000000U)

Adjust the value of External High Speed oscillator (HSE) used in your application. This value is used by the RCC HAL module to compute the system frequency (when HSE is used as system clock source, directly or through the PLL).

Value of the External oscillator in Hz

◆ HSI48_VALUE

#define HSI48_VALUE ((uint32_t)48000000U)

Internal High Speed oscillator for USB (HSI48) value.

Value of the Internal High Speed oscillator for USB in Hz. The real value may vary depending on the variations in voltage and temperature.

◆ HSI_VALUE

#define HSI_VALUE ((uint32_t)16000000U)

Internal High Speed oscillator (HSI) value. This value is used by the RCC HAL module to compute the system frequency (when HSI is used as system clock source, directly or through the PLL).

Value of the Internal oscillator in Hz

◆ LSE_STARTUP_TIMEOUT

#define LSE_STARTUP_TIMEOUT ((uint32_t)5000U)

Time out for LSE start up, in ms

◆ LSE_VALUE

#define LSE_VALUE ((uint32_t)32768U)

External Low Speed oscillator (LSE) value. This value is used by the UART, RTC HAL module to compute the system frequency.

< Value of the Internal Low Speed oscillator in Hz The real value may vary depending on the variations in voltage and temperature. Value of the External oscillator in Hz

◆ LSI_VALUE

#define LSI_VALUE ((uint32_t)37000U)

Internal Low Speed oscillator (LSI) value.

LSI Typical Value in Hz

◆ MSI_VALUE

#define MSI_VALUE ((uint32_t)2097000U)

Internal Multiple Speed oscillator (MSI) default value. This value is the default MSI range value after Reset.

Value of the Internal oscillator in Hz

◆ TICK_INT_PRIORITY

#define TICK_INT_PRIORITY ((uint32_t)0U)

tick interrupt priority

◆ VDD_VALUE

#define VDD_VALUE ((uint32_t)3300U)

This is the HAL system configuration section.

Value of VDD in mv

Macros